Posted at 17-01-2017
The PK7 from Tervasaari mill Valkeakoski will be transferred to Skarbläcka, Swedend. MARGIz is part of this project as the dismantling team.
The biggest challenge represents the transfer of an 160 Tons Yankee Cylinder which is scheduled for beginning June. There are a few companies involved in this procedure, each with its specific task. Timing is essential. This sensitive heavy part must arrive undamaged in Sweden.
The biggest challenge represents the transfer of an 160 Tons Yankee Cylinder which is scheduled for beginning June. There are a few companies involved in this procedure, each with its specific task. Timing is essential. This sensitive heavy part must arrive undamaged in Sweden.
News and galleries related to this project: 10
Posted at 13-12-2017
MARGIZ was a key part of the project of transferring the PM7 from Tervasaari to Skärblacka. Here is a short movie about the new PM10 ...
Posted at 16-08-2017
Project of dismantling and scrapping of elements and removing of residues after dismantling PM7 paper machine has came to an end. We were working on this project in Valkeakoski, in Finland, for our client - BillerudKorsnas company. During two months we dismantled almost 400 tones of elements made of copper, ...
Posted at 24-07-2017
We present some pictures taken during preparing for transport of 160 tones Yankee Cylinder
Posted at 20-06-2017
Dismantling PM7 machine in Valkeakoski is already finished.
We started this project in January 2017, and since then we have dismantled the machine, match marked and sent to re-erection destination. We have also scrapped all of the metal elements and cables, that were not sent, and which are not a part ...
We started this project in January 2017, and since then we have dismantled the machine, match marked and sent to re-erection destination. We have also scrapped all of the metal elements and cables, that were not sent, and which are not a part ...
Posted at 07-06-2017
Headbox is a part of paper machine, which is located in wet section. That is where begins the whole process of formation paper products. By dismantling, and moving that part, we ended Valkeakoski project. Headbox was covered with wooden bars for its protection, and lifted with thirty-tones overhead crane.
See ...
See ...
Posted at 06-06-2017
At the beginning of June, as a main, and one of final part to finish Tervasaari project in Valkeakoski, we moved 160 tons Yankee cylinder over top wall of the factory building.
Moving on special rails, the cylinder was rolled through the open building wall and loaded onto a special over-sized trailer.
Our ...
Moving on special rails, the cylinder was rolled through the open building wall and loaded onto a special over-sized trailer.
Our ...
Posted at 09-04-2017
Drying section in a paper machine is a key step in achieving the final moisture content of the paper, up to 10%, depending on the type of paper produced. Drying paper sheets with cylinders consumes huge layers of hot air. In paper machines, which produce thin paper or tissue paper are most commonly used ...
Posted at 02-04-2017
After the oil layer, paper layer and plastic foil layer, we add wood planks all around the Yankee to protect the shell. The removal of the three pieces of hood was done after the Yankee was fully covered. After the hood is removed we will continue to dismantle the frame structure on upper sides of the ...
Posted at 22-02-2017
In mid-January, MARGIZ began to prepare the dismantling of a paper machine in Valkeakoski, Finland. The PM7 will be transferred in Sweden and rebuild with some modifications.
Our match-marking team start to label the paper machine before the dismantling team arrived on 1st of February. At the moment,the ...
Our match-marking team start to label the paper machine before the dismantling team arrived on 1st of February. At the moment,the ...
Posted at 20-10-2016
On October 2016 we have visited the Tervasaari PK 7 in Valkeakoski to meet with the customer and evaluate the works, in order to place an offer. Here are a few pictures of the mill.
Our work
We are a German-Polish Company, our main objective is innovative dismantling and assembly of equipment and production lines. Matchmarking, dismantling, loading and shipping, of materialand finally re-... Read more
|
Our team
Our team consists of highly skilled workers: mechanics, electricians, electronic technicians, welders. From dismantling to re-erection, all project phases are handled and carefully documented for our Customer. Read more
|
Our tools
For every task we provide the best solution! Forklifts, cranes and special lifting equipment, tools for dismantling and overhauling, MARGIZ can provide and handle. Our own specific software used for m.... Read more
|